Technical Specifications
Input Ratings
| Supply Voltage | 200 – 240V ± 10%
380 – 480V ± 10%
500 – 600V ± 10% |
| Supply Frequency | 48 – 62Hz |
| Displacement Power Factor | > 0.98 |
| Phase Imbalance | 3% Maximum allowed |
| Inrush Current | < rated current |
| Power Cycles | 120 per hour maximum, evenly spaced |
Output Ratings
| Output Power | 230V 1 Phase: 0.75–2.2kW / 1–3HP
230V 3 Phase: 0.75–75kW / 1–100HP
400V 3 Phase: 0.75–250kW
460V 3 Phase: 1–350HP
575V 3 Phase: 0.75–110kW / 1–150HP |
| Overload Capacity | 150% for 60 seconds |
| Output Frequency | 0 – 500Hz, 0.1Hz resolution |
| Acceleration Time | 0.01 – 600 seconds |
| Deceleraton Time | 0.01 – 600 seconds |
| Typical Efficiency | 98% |
Ambient Conditions
| Temperature | Storage : −40 to 60°C
Operating : −10 to 50°C |
| Altitude | Up to 1000m ASL without derating
Up to 2000m maximum UL Approved
Up to 4000m maximum (non UL) |
| Humidity | 95% Max, non-condensing |
| Vibration | Conforms to IEC 60068-2-6
Sinusoidal Vibration
10 - 57Hz @ 0.075mm Pk
57 - 150Hz @ 1g Pk |
Enclosure
| Ingress Protection | IP20, IP55, IP66 |
Programming
| Keypad | Built-in keypad as standard
Optional remote mountable keypad |
| Display | Built-in multi language text display (IP55 & IP66)
7 Segment LED (IP20) |
| PC | OptiTools Studio |
Control Specification
| Control Method | V/F Voltage Vector
Energy Optimsied V/F
3GV Sensorless Vector Speed Control
3GV Sensorless Vector Torque Control
Closed Loop (Encoder) Speed Control
Closed Loop (Encoder) Torque Control
PM Vector Control
BLDC Control
Synchronous Reluctance |
| PWM Frequency | 4 – 32kHz Effective |
| Stopping Mode | Ramp to Stop: User Adjustable 0.01–600 secs
Coast to Stop |
| Braking | Motor Flux Braking
Built-in Braking Transistor |
| Skip Frequency | Single point, user adjustable |
| Setpoint Control | Analog Signal | 0 to 10 Volts
10 to 0 Volts
−10 to 10 Volts
0 to 20mA
20 to 0mA
4 to 20mA
20 to 4mA |
| Digital | Motorised Potentiometer (Keypad)
Modbus RTU
CANopen |
Fieldbus
| Built in | CANopen | 125 – 1000kbps |
| Modbus RTU | 9.6 - 115.2 kbps selectable
8N1, 8N2, 8E1, 8O1 |
I/O Specification
| Power Supply | 24 Volt DC, 100mA, Short Circuit Protected
10 Volt DC, 10mA for Potentiometer |
| Programmable Inputs | 5 Total as standard (Optional additional 3)
3 Digital (Optional additional 3)
2 Analog / Digital Selectable |
| Digital Inputs | Opto - Isolated
8 – 30 Volt DC, internal or external supply
Response time < 4ms |
| Analog Inputs | Resolution : 12 bits
Response time : < 4ms
Accuracy : < 1% full scale
Parameter adjustable scaling and offset |
| PTC Input | Motor PTC / Thermistor Input
Trip Level : 3kΩ |
| Programmable Outputs | 4 Total (Optional additional 3)
2 Analog / Digital
2 Relays (Optional additional 3) |
| Relay Outputs | Maximum Voltage : 250 VAC, 30 VDC
Switching Current Capacity : 5A AC , 5A DC |
| Analog Outputs | 0 to 10 Volt
0 to 20mA
4 to 20mA |
Application Features
| PID Control | Internal PID Controller
Multi Setpoint Select
Standby / Sleep Mode
Boost Function |
| Hoist Mode | Dedicated Hoist Mode
Motor Holding Brake Pre-Torque & Control
Over Limit Protection |
Maintenance & Diagnostics
| Fault Memory | Last 4 Trips stored with time stamp |
| Data Logging | Logging of data prior to trip for diagnostic purposes : Output Current, Drive Temperature, DC Bus Voltage |
| Maintenance Indicator | Maintenance Indicator with user adjustable maintenance interval
Onboard service life monitoring |
| Monitoring | Hours Run Meter
Resettable & Non Resettable kWh meters
Cooling Fan Run Time |
Standards
| Low Voltage Directive | 2014/35/EU |
| EMC Directive | 2014/30/EU |
| Additional Conformance | UL, cUL, EAC, RCM |
| Marine Certification | DNV Type Approval |
| Environmental Conditions | Designed to meet IEC 60721-3-3, in operation:
IP20 Drives: 3S2/3C2
IP55 & 66 Drives: 3S3/3C3 |
Connection Diagram
| Terminal | Function | Default Setting |
|
| 1 | 24 Volt DC Output, 100mA max / 24 Volt DC Input |
| 2 | Digital Input 1 | Drive Enable |
| 3 | Digital Input 2 | Forward/Reverse Select |
| 4 | Digital Input 3 | Preset Speed 1 Select |
| 5 | +10 Volt Power Supply 5mA |
| 6 | Analog Input 1 | Speed Reference 0–10 Volt |
| 7 | 0 Volt | |
| 8 | Analog Output 1 | Motor Speed |
| 9 | 0 Volt | |
| 10 | Analog Input 2 | |
| 11 | Analog Output 2 | Motor Current |
| 12 | Safe Torque Off Input | |
| 13 | Safe Torque Off Input | |
|
| 14 | Output Relay 1 | Drive Healthy/Fault |
| 15 |
| 16 |
|
| 17 | Output Relay 2 | Drive Running |
| 18 |